Comfort and control, built in
Smart Home Automation and Heated Surfaces in Toronto & the GTA
Smart home automation for a Kings Valley Homes project means planning a hub-based system—lights, climate, and AV—alongside heated floors and heated driveways so everything is pre-wired during framing and finishing. Across Markham, Toronto, Richmond Hill, Vaughan, Newmarket, and Aurora, homeowners increasingly want integrated control rather than a drawer of disconnected gadgets. Invisible and recessed speakers are easiest when speaker locations and low-voltage runs are set at rough-in. Call (647) 278-2494 for a free consultation.
One team for design, permits and construction

Who it is for
The right brief, before the first drawing.
This service suits homeowners already building or renovating with us who want daily comfort and simple control: lighting scenes, zoned temperature, AV with invisible or recessed speakers, and heated floors or a heated driveway for GTA winters—especially when infrastructure can be decided before walls close.
How the work proceeds
How a smart home installation runs, step by step
Consultation & priorities
We map which rooms need lighting scenes, climate zones, AV, invisible speakers, and heated surfaces, and what must stay simple to operate.
Design integration
Hub strategy, device locations, cable paths, heating layouts, and electrical loads are drawn into the project—not bolted on later.
Rough-in during construction
Trades place wiring, speaker locations, sensors, and heating elements while framing and mechanical work are open.
Finish, configure & test
Devices, keypads, thermostats, and media endpoints are installed; scenes and schedules are set and checked.
Walkthrough & handoff
We show you how to live with the system day to day, including local controls when you do not want to use an app.
Timeline
What affects a smart home installation timeline
Smart home and heated-surface work follows your broader custom home, renovation, or addition schedule. On its own it rarely extends the project when decisions land before rough-in. Lead times for equipment, the number of rooms and systems, heated floor or driveway scope, and coordination with electrical and mechanical trades set the pace inside that overall timeline.
What affects cost
What drives smart home automation cost
- Number of rooms and systems on the hub (lighting, climate, AV)
- Invisible or recessed speaker count and finish detailing
- Heated floor coverage and driveway area
- Network, cabling, and control complexity
- Integration with existing equipment versus a clean new install
We do not publish package prices. A free consultation is the right place to talk through scope before anyone suggests a number.
A smart home that works is mostly wiring, networking and planning, decided while the walls are still open. The devices are the easy part. This section explains the infrastructure choices, the electrical rules and the privacy habits behind a system that stays reliable and easy to live with.
Infrastructure first, devices second
Devices change every few years. The infrastructure behind the walls is there for decades, so it is worth getting right.
- Network. A wired backbone to access points and to the places that need reliability (media, workstations, cameras) is more dependable than Wi-Fi alone. Cable runs and equipment space are planned at rough-in.
- Power. Dedicated power and a clean place for the network and control equipment avoid surface wiring later.
- Lighting control. Switch locations, neutral wires and dimming needs are decided at framing, since many smart switches need a neutral at the box.
- Thermostats and sensors. Low-voltage wiring and sensor locations are planned alongside the heating and cooling design.
- Shades, speakers and AV. Pre-wire and recessed housings are placed before drywall; adding them afterwards means opening finished walls.
Standards, and why they matter
Matter is an open, IP-based smart home standard. Matter devices connect over Wi-Fi, Ethernet or Thread, are commissioned using Bluetooth Low Energy, and are controlled locally through a Matter controller. Choosing devices that support open standards makes a system easier to keep working if a single manufacturer changes direction. It does not remove the need for good wiring, and it does not make every device compatible with every other.
We keep local control in the design: wall keypads, switches and thermostats that still work when the internet or an app does not.
Electrical, ESA and low-voltage rules
The Electrical Safety Authority regulates electrical work in Ontario. A licensed electrical contractor files the notification of work, and homeowners who do their own electrical work must file it themselves.
- Low-voltage wiring. In an owner-occupied dwelling, notification is not required for Class 2 low-voltage wiring (limited to 100 VA and 30 V rms or 60 V dc). Power over Ethernet, or anything above Class 2, does require notification.
- Line-voltage wiring and devices such as dimmers, switches, outlets and fixtures are electrical work that follows the Ontario Electrical Safety Code.
- Inspections. Where a notification is filed, the work is inspected by ESA before it is covered.
This is one reason smart home planning belongs in the electrical rough-in rather than after it.
Heated floors and driveways
Radiant heat is popular in bathrooms, entries and driveways in Toronto winters. There are two kinds, and they run on different rules.
- Electric heating cable or mat. Installed under tile or concrete, controlled by a thermostat with a floor sensor. It is electrical work and must be reported to ESA by a licensed contractor.
- Hydronic (heated water) systems. Tubing circulates warm water from a boiler or heat source. This is a heating and plumbing system, which in Toronto needs a permit, and gas-fired equipment is installed by a TSSA-certified technician.
A heated driveway also needs design for drainage, controls and snow-melt sensors. Heated surfaces are planned with the structure, the finish and the electrical or mechanical design so each one fits the others.
Privacy and security of connected devices
A connected home is a network. A few habits make it safer.
- Strong, unique passwords and two-factor authentication on controller and camera accounts.
- Separate networks for guests and for smart devices.
- Firmware updates kept current.
- Local recording or local control where possible.
- Cameras aimed at your own property. The Office of the Privacy Commissioner of Canada notes that personal-use home cameras are generally outside federal private-sector privacy law, but recordings still need to be secured and used responsibly.
How a smart home project runs
- Priorities We map which rooms and systems matter, and what must stay simple.
- Design Control strategy, device locations, cable paths and electrical loads are drawn into the project.
- Rough-in Wiring, speaker housings, sensors and heating elements are installed while walls are open, with inspections as required.
- Finish and commission Devices, keypads and thermostats are installed, and scenes and schedules are configured.
- Test and handoff We test every control, walk you through daily use and leave you with documentation.
What shapes the schedule
Beyond the general note on this page, the schedule depends on:
- Whether decisions are final before electrical rough-in.
- Lead times for lighting control, thermostats, AV and heating products.
- ESA and permit inspections on electrical, heating and plumbing.
- Programming and testing, which come after the finishes are done.
What drives cost, without a number
The main drivers are:
- The number of rooms, circuits and devices.
- The scope of the network and cabling, including recessed and invisible speakers.
- Heated floor coverage and driveway area, and whether the heat is electric or hydronic.
- Control complexity and the brand ecosystem chosen.
- New installation in a build versus integration with existing equipment in a renovation.
We talk through scope in a free consultation, before anyone suggests a number.
More questions, answered
More questions, answered
Do I need a hub?
Not always. Modern open standards let some devices work with a controller you already own. A central controller still helps with scenes, schedules and local control, and we choose it for your setup.
Is Wi-Fi enough?
For basic devices, yes, but the network behind it should be wired where reliability matters, such as access points, media and cameras.
Does low-voltage wiring need an ESA notification?
Not in an owner-occupied dwelling for Class 2 wiring up to 100 VA and 30 V rms or 60 V dc. Power over Ethernet or anything above Class 2 requires notification.
Can I add smart features to an existing house?
Yes, but it is easier if walls are open. In a renovation, we plan around the walls being opened for other reasons, and use wireless devices where wiring is impractical.
Are heated floors worth it?
They add comfort in bathrooms and entries. The type, the controls and the floor build-up matter, and electric systems need ESA notification while hydronic systems are a plumbing and heating matter.
What happens if the internet goes down?
A well-designed system keeps local controls working: wall keypads, switches and thermostats do not depend on an app or the internet.
Sources
Regulatory details checked against the sources below in October 2026. Municipal rules change; we confirm current requirements for your address during your consultation.
Adding smart-home controls or heated floors? Call us while it's still in planning.
Questions about this service
Quick answers.
Can smart home features be added during a renovation?
Yes. Renovations and additions that open walls or ceilings are strong moments for hubs, lighting control, AV, and speakers. Full gut renovations allow cleaner pre-wire; lighter renovations may limit runs. We assess what is practical on your property during consultation.
What are invisible or recessed speakers?
They are speakers designed to sit in ceilings or walls—or behind architectural finishes—so sound is present without large boxes on shelves. Locations and wiring are planned at rough-in so plaster, paint, and trim stay clean.
Do I need a single brand for everything?
Not necessarily. What matters is a coherent plan: power, network, control points, and which functions must work together. We help you choose a practical stack for your build; we do not lock you into partnerships we do not have.
Will heated floors work with any flooring?
Suitability depends on the heating method and the finished floor product. We coordinate heating layouts with flooring selections so comfort and material warranties stay aligned.
Which areas do you serve?
We incorporate smart home automation and heated surfaces into projects across Markham, Toronto, Richmond Hill, Vaughan, Newmarket, and Aurora, typically as part of a custom home, renovation, or addition.
Related services
- Home security systems — home security system planning and installation.
- Home renovation — whole-home renovations in Toronto and the GTA.
- Kitchen renovation — kitchen layouts, cabinetry, finishes and installation.
Free consultation
Book your free consultation today
Call (647) 278-2494 or email info@kingsvalleyhomes.ca. Tell us the municipality, the property, and what you want the home to do next.
